| Operating Weight | 52781 kg |
|---|---|
| Rated Payload - Loose Material (Standard) | 14.5 t |
| Rated Payload - Standard (Quarry Face) | 11.3 t |
| Operating Weight - Standard | 52781 kg |
| Operating Weight - High Lift | 54258 kg |
| Bucket Capacity Range | 4.7-13 m3 (6.2-17 yd3) |
| Bucket Capacities | 4.7-13 m3 (6.2-17 yd3) |
|---|
| Engine Model | Cat® C18 ™ |
|---|---|
| Engine Power - ISO 14396 | 432 kW |
| Rated Speed | 1,700 rpm |
| Peak Power Speed | 1,500 rpm |
| Peak Torque - 1,200 rpm - SAE J1995 | 3023 N·m |
| Torque Rise | 58% |
| Bore | 145 mm |
| Stroke | 183 mm |
| Displacement | 18.1 l |
| Emissions | U.S. EPA Tier 4 Final, EU Stage V, and Japan 2014 |
| Gross Power - SAE J1995 | 439 kW |
| Net Power - SAE J1349 | 401 kW |
| Forward 1 (virtual) | 7 km/h |
|---|---|
| Forward 2 (virtual) | 11.3 km/h |
| Forward 3 (virtual) | 22.2 km/h |
| Forward 4 (virtual) | 32.1 km/h |
| Reverse 1 (virtual) | 7 km/h |
| Reverse 2 (virtual) | 11.3 km/h |
| Reverse 3 (virtual) | 28.2 km/h |
| Transmission Type | Cat switched reluctance electric drive |
| Front | Fixed |
|---|---|
| Oscillation Angle | 13° |
| Rear | Trunnion |
| Lift/Tilt System - Circuit | EH-Positive Flow Control, Flow Sharing |
|---|---|
| Maximum Flow at 1,400-1,600 rpm | 580 l/min |
| Relief Valve Setting - Lift/Tilt | 32800 kPa |
| Lift Cylinder - Bore | 210 mm |
| Lift Cylinder - Stroke | 1050 mm |
| Lift/Tilt System - Pump | Variable displacement piston |
| Tilt Cylinder - Bore | 269 mm |
| Tilt Cylinder - Stroke | 685 mm |
| Total Steering Angle | 86° |
|---|---|
| Steering Cycle Times - High Idle | 3.4 s |
| Steering Cycle Times - Low Idle | 5.6 s |
| Maximum Flow at 1,400-1,600 rpm | 270 l/min |
| Steering Cut Off Pressure | 30000 kPa |
| Steering System - Circuit | Pilot, load sensing |
| Steering System - Pump | Piston, variable displacement |
| Fuel Tank | 555 l |
|---|---|
| Transmission | 60 l |
| Differential - Final Drives - Front | 186 l |
| Note | All nonroad Tier 4 Final/Stage V diesel engines are required to use: – The machine has the flexibility to run on either ultra-low-sulfur diesel fuel (ULSD with 15 ppm of sulfur or less). – Cat engines are compatible with the following renewable, alternative, and biodiesel* fuels that reduce greenhouse gases: Up to B20 biodiesel (FAME) ** Up to 100% HVO and GTL renewable fuels * Refer to guidelines for successful application. Please consult your Cat dealer or “Caterpillar Machine Fluids Recommendations” (SEBU6250) for details. – Cat DEO-ULS™ or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specifications are required. – Only use DEF that meets ISO 22241-1 standards. |
| Differential - Final Drives - Rear | 186 l |
| Engine Crankcase | 60 l |
| Cooling System - Jacket Water | 112 l |
| Cooling Systems - Power Train | 30 l |
| Diesel Exhaust Fluid Tank | 33 l |
| Hydraulic System - Implement/Steering | 475 l |
| Brakes | ISO 3450:2011 |
|---|
| Operator Sound Level (ISO 6396) | 72 dB(A) |
|---|---|
| Machine Sound Level (ISO 6395) | 109 dB(A) |
| Note (1) | The operator sound pressure level was measured according to the test procedures and conditions specified in ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
| Note (2) | Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. |
| Note (3) | The machine sound power level was measured according to the test procedures and conditions specified in ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. |
| Air Conditioning | The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. |
|---|
| Dump Angle at Maximum Lift | -39.4 ° |
|---|---|
| Fork Height at Maximum Lift | 5242 mm |
| Fork Height with Level Arms | 2474 mm |
| Fork Top Clamp Opening | 4006 mm |
| Front Axle Centerline to Fork Tip | 5023 mm |
| Ground to Bumper Clearance | 933 mm |
| Ground to Center of Front Axle | 978 mm |
| Ground to Lower Hitch Clearance | 568 mm |
| Ground to Top of Exhaust Stacks | 4214 mm |
| Ground to Top of Hood | 3334 mm |
| Ground to Top of ROPS | 4221 mm |
| Hinge Pin Height at Maximum Lift | 4918 mm |
| Maximum Overall Length | 12761 mm |
| Rear Axle - Centerline to Bumper | 3187 mm |
| Wheel Base | 4550 mm |
| Dump | 2.2 s |
|---|---|
| Lower Float Down | 3.5 s |
| Rack Back | 4.5 s |
| Raise | 8 s |
| Total Hydraulic Cycle Time | 18.2 s |
| ROPS/FOPS | ROPS/FOPS meet ISO 3471:2008 and ISO 3449:2005 Level II standards |
|---|
| Ground to Top of ROPS | 4202 mm |
|---|---|
| Ground to Top of Exhaust Stacks | 4498 mm |
| Ground to Top of Hood | 3334 mm |
| Ground to Bumper Clearance | 933 mm |
| Rear Axle - Centerline to Bumper | 3187 mm |
| Front Axle Centerline to Bucket Tip | 14 mm |
| Wheel Base | 4550 mm |
| Maximum Overall Length | 11991 mm |
| Ground to Lower Hitch Clearance | 568 mm |
| Ground to Center of Axles | 978 mm |
| Clearance at Maximum Lift | 3641 mm |
| B-Pin Height - Maximum Lift | 5479 mm |
| Maximum Overall Height - Bucket Raised | 7455 mm |
| Reach - Maximum Lift | 1981 mm |
| Note | Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height. |
| Ground to Top of ROPS | 4202 mm |
|---|---|
| Ground to Top of Exhaust Stacks | 4498 mm |
| Ground to Top of Hood | 3334 mm |
| Ground to Bumper Clearance | 933 mm |
| Rear Axle - Centerline to Bumper | 3187 mm |
| Front Axle Centerline to Bucket Tip | 4661 mm |
| Wheel Base | 4550 mm |
| Maximum Overall Length | 12398 mm |
| Ground to Lower Hitch Clearance | 568 mm |
| Ground to Center of Axles | 978 mm |
| Clearance at Maximum Lift | 4043 mm |
| B-Pin Height - Maximum Lift | 5881 mm |
| Maximum Overall Height - Bucket Raised | 7849 mm |
| Reach - Maximum Lift | 2062 mm |
| Note | Specs are calculated with 6.9 m3 (9.0 yd3) rock bucket and Michelin XLDD2 with 978 mm (3.2 ft) centerline of rear axle height. |
| Recyclability | 96% |
|---|
